Engineering

When would you use a reamer versus a boring bar? Discuss.

Tapping: M10x1.50 mm & ¼-20 tapped hole (2)
What is the drill diameter of your drills?
______________.
______________.
What is the percentage thread engagement for this diameter? (1.5)
______________.
______________.

What are the speed and feed values of these drills and taps? Clearly state your cutting speed data along with the references, and the appropriate units.

List three typical tap types, and when they are used.

Reaming: For an 8F7 hole: (5)
What is the diameter of your drill you would use? ______________.
What reamer would you use and why? ______________.

Material Drill Reamer
Feeds
Speeds
Time
Other characteristics:

Quickies
Which of the following statements is not correct?
a) core drills have 3 or 4 flutes.
b) high helix drills help in chip removal.
c) straight fluted drills are used for sheet metal.
d) centre drills are for long holes, such as gun barrels.

If we want a hole with a 1/2-13-UNC thread, what size of tap drill should be used?

If we want a hole with a 6 x 1.0 thread, what size of tap drill should be used?

What size is an F drill?

List three reasons that machining operations may be required, and provide an example for each. Do not provide duplicate information.
What special precautions are needed when cutting magnesium, and thermoplastic materials (such as ABS plastic)?
When considering the basic metal-cutting process, what are the important physical and chemical properties of a cutting tool?

Tool materials can have conflicting properties when used for machining operations. Discuss. Use numerical examples to justify your answer, and reference appropriately. (Hint: consider tool costs, tool life, processing time, potential failure modes).
Explain whether it is desirable to have a high or low (a) n value and (b) C value in the Taylor tool-life equation. You may develop an example to assist with your explanation.
Describe the difficulties that may be encountered in clamping a workpiece made of a soft metal in a three-jaw chuck or a vise.
It has been stated that titanium-nitride coatings allow cutting speeds and feeds to be higher than those for uncoated tools. Survey the technical literature and prepare a table showing the percentage increase of speeds and feeds that would be made possible by coating the tools.
List the concerns you would have if you needed to economically machine carbon-fiber reinforced polymers or metal-matrix composites with graphite fibers in an aluminum matrix.
Contact several different suppliers of cutting tools, or search their websites. Make a list of the costs of typical cutting tools as a function of various sizes, shapes, and features.

Engineering

When would you use a reamer versus a boring bar? Discuss.

Tapping: M10x1.50 mm & ¼-20 tapped hole (2)
What is the drill diameter of your drills?
______________.
______________.
What is the percentage thread engagement for this diameter? (1.5)
______________.
______________.

What are the speed and feed values of these drills and taps? Clearly state your cutting speed data along with the references, and the appropriate units.

List three typical tap types, and when they are used.

Reaming: For an 8F7 hole: (5)
What is the diameter of your drill you would use? ______________.
What reamer would you use and why? ______________.

Material Drill Reamer
Feeds
Speeds
Time
Other characteristics:

Quickies
Which of the following statements is not correct?
a) core drills have 3 or 4 flutes.
b) high helix drills help in chip removal.
c) straight fluted drills are used for sheet metal.
d) centre drills are for long holes, such as gun barrels.

If we want a hole with a 1/2-13-UNC thread, what size of tap drill should be used?

If we want a hole with a 6 x 1.0 thread, what size of tap drill should be used?

What size is an F drill?

List three reasons that machining operations may be required, and provide an example for each. Do not provide duplicate information.
What special precautions are needed when cutting magnesium, and thermoplastic materials (such as ABS plastic)?
When considering the basic metal-cutting process, what are the important physical and chemical properties of a cutting tool?

Tool materials can have conflicting properties when used for machining operations. Discuss. Use numerical examples to justify your answer, and reference appropriately. (Hint: consider tool costs, tool life, processing time, potential failure modes).
Explain whether it is desirable to have a high or low (a) n value and (b) C value in the Taylor tool-life equation. You may develop an example to assist with your explanation.
Describe the difficulties that may be encountered in clamping a workpiece made of a soft metal in a three-jaw chuck or a vise.
It has been stated that titanium-nitride coatings allow cutting speeds and feeds to be higher than those for uncoated tools. Survey the technical literature and prepare a table showing the percentage increase of speeds and feeds that would be made possible by coating the tools.
List the concerns you would have if you needed to economically machine carbon-fiber reinforced polymers or metal-matrix composites with graphite fibers in an aluminum matrix.
Contact several different suppliers of cutting tools, or search their websites. Make a list of the costs of typical cutting tools as a function of various sizes, shapes, and features.